PART NO. 03254 Rev. 2PRINTED 3/2010PRINTED IN USA© 2010Scag Power EquipmentDivision of Metalcraft of Mayville, Inc.This manual contains the operating
7RSection 33-3/4”4-1/2”0.40”3-3/4”4-1/2”TemplateTemplateCenter Punch &Drill 11/32” HoleCenter Punch &Drill 11/32” HoleDischarge ChuteMounting
8RSection 3Install the front hinge bracket to the cutter deck using 14. two (2) 5/16-18 x 3/4" bolts and two (2) 5/16-18 elastic stop nuts. See F
9RSection 3Tighten the hardware.21. Install the OCDC discharge chute to the cutter deck. 22. Secure using two (2) 5/16-18 x 1-3/4" bolt and two (
10RSection 3INSTALLATION INSTRUCTION FOR 3.2 STT-61V Prepare the machine so there is easy and safe access to the work area. Park the machine on a fl
11RSection 33-3/4”4-1/2”0.40”3-3/4”4-1/2”TemplateTemplateCenter Punch &Drill 11/32” HoleCenter Punch &Drill 11/32” HoleDischarge ChuteMounting
12RSection 3Determine which OCDC control lever weldment is 18. needed. The "curved" control lever is used for most STT models with a 61V cut
13RSection 3Replace decal p/n 483406. Install on the left side of 28. the cutter deck in the location shown in Figure 3-17483406 DecalLocation 483406
14RSection 3AABBOCDC DischargeChuteUpper ControlLinkOCDC Discharge Chute InstallationFigure 3-18.
15RSection 8SCAG APPROVED ATTACHMENTS AND ACCESSORIES.8.1 Attachments and accessories manufactured by companies other than Scag Power Equipment are no
16RSection 8STT-52V / STT-61V OCDCST T-52VST T-61VAABBABCCSTT-52VSTT-61VCDDD*STT-52VSTT-61VEFEFEF27272929*52V Straight Lever Weldment used on STT-61V
WARNINGFAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY OR DEATH.Read this manual completely as well as other manuals that cam
17RSection 8STT-52V / STT-61V OCDCRef. No.Part No. Description123456789101112131415161718192021222324252627282930313248401004020-12*452088452073452089
LIMITED WARRANTY- COMMERCIAL ACCESSORYAny part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to
IRTable of ContentsTable of ContentsGENERAL INFORMATIONSECTION 1 - ...
1RSection 1INTRODUCTION1.1 Your OCDC was built to the highest standards in the industry. However, the prolonged life and maximum efficienc
2RSection 1SYMBOLS1.4 SYMBOL DESCRIPTION SYMBOL DESCRIPTION Choke Transmission Parking Brake 48071SSpinning Blade On/Start Spring Tension on Idler Off
3RSection 2INTRODUCTION2.1 Your mower is only as safe as the operator. Carelessness or operator error may result in serious bodily injury or d
4RSection 2When using any attachment, never direct the 2. discharge of material toward bystanders or allow anyone near the machine while in operation.
5RSection 2OPEN POSITIONIn the open position, the clippings will side discharge.Pull up on the OCDC control handle to unlock from 1. the closed positi
6RSection 3INSTALLATION INSTRUCTION FOR 3.1 STT-52VPrepare the machine so there is easy and safe access to the work area. Park the machine on a flat
Comentarios a estos manuales